CleanSpace Encapsulation (Before)
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation (Before)
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation (Before)
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation (Before)
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation (Before)
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber,to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.
CleanSpace Encapsulation
In order to prevent water from pooling in the crawlspace from exterior seepage, we installed a full perimeter interior dewatering system with the sump pump. We dug an interior drainage trench system, roughly 12 inche wide throughout the perimeter of the crawlspace. Inside the trenches we laid filter cloth that covers the entire bed of soil and ran the tile to a SuperSump pump. Lastly, we placed a bed of stone over the tile to allow extra drainage and to cover the trench. We placed a SuperSump pump in the south east corner with the plumbing running out the side of the foundation. There was an area of the foundation that continued to wash sediments into the crawlspace. The foundation was built with a concrete grade beam rather than a traditional concrete footing. In order to prevent future erosion in this area, we dug down to the bottom of the wall on the exterior and poured a concrete underfooter. In order to control excess humidity and moisture in the crawlspace, nova is to install the Cleanspace a Encapsulation liner. The process of installing the encapsulation membrane will be to install the wall liner around the full perimeter of the crawlspace. Currently there is 2 inch foam panels on the foundation wall, we will use 2 1/2 inch plastic anchors to mechanically fastened the encapsulation liner and foam to the foundation wall. Next, we applied CleanSpace Encapsulation along the walls and floors of the crawlspace. The point of the encapsulation is to isolate the airspace from the soil as well as the moisture that is caused by temperature change on the foundation. This allows the air space to be conditioned. Finally, an AprilAire full crawlspace dehumidifier was installed in order to extract moisture from the air space, and more importantly the lumber, to prevent mold growth from occurring in the future.